Friends who have satellite antennas (commonly known as big pots) installed at home, are you still worried about not being able to receive premium channels such as Central Five and Central Six? Are you still "watching the stage and sighing" for those encrypted programs? Now this wish can come true! Just move your fingers, press the remote control a few times and you're done!

The steps are as follows: first find "Transponder Settings" in the menu, then click "Add Transponder", set the "Downlink Frequency" to 03881, "Symbol Rate" to 27500, and "Polarity" to Level can receive central fifth and sixth grade.

Want more channels? Set the downlink frequency to 04061, the symbol rate to 27500, and the polarity to vertical to receive channels such as "CCTV Premium" and "Fengyun Music", which are equally exciting!

Please read below for more channels. Below, I will tell you in the order of "downlink frequency", "symbol rate" and "polarity": 03981, 27499, vertical; 04021, 27499, vertical; 04141, 27500, vertical; 03921, 27500, horizontal

Note: I am talking about the ChinaStar 6 satellite.

Warning: Different brands of cauldrons may not necessarily follow my steps. I hope everyone can adapt (I have also seen one. If there are four colored buttons at the bottom of your remote control, press the red one. You can find it) Some friends are worried that they will lose their original channels. I will tell you that this can only be added and cannot be reduced! Upgrading and Cracking Small Satellite Pots Currently, many methods for cracking satellite upgrades using fake pots have been circulated on the Internet. Here are a few methods that some netizens have successfully practiced? Hope it helps everyone.

Cracking method one: manual search

Since the upgrade of China Star 99 satellite, some copycat phones cannot complete the automatic upgrade when they are turned on. After turning on the computer, it will automatically search for 39 and then it will crash. At this time, the remote control fails and cannot be exited. Notice! This is not a deadlock.

Solution: Unplug the signal cable, and the automatic search will be completed. Since there is no signal search, after the search is completed, it will display that 0 TV sets have been found. However, the remote control can be used at this time but the receiver is still in a no-program state. . Then connect the signal line, enter the menu, and manually search the four groups of transponders. Notice! Be sure to do it manually, as automatic search will crash again. After the manual search is completed, the receiver can resume normal operation. You can try it!

Crack method two: restore factory settings

I tried it today and the upgrade program did enter the receiver. But if you start the upgrade program, only the serial numbers change from 01, 1001, 004 to 06, 10001, 004, and the upgrade bar does not change at all. Then it automatically enters automatic search. After reaching 39, the progress bar stops moving. But the frequency points are increasing and changing. You interrupt and exit. Not a single program was reserved. If you don’t interrupt the rollout, the frequency will keep increasing. It looks like it's dead. The solution is to enter settings, return to factory status, password 9999 or 0000. Then enter manual search. There are no programs on frequency 1. Enter frequency 2 and search and there will be programs. Frequencies 3 and 4 also have programs, 2, 3, and 4. There are 54 programs on one frequency. Same as before.

Cracking method three: Upgrade the copycat machine

Upgrade Zhongjiu machine to machine, one mother machine. In fact, it is the machine that can be viewed currently. One serial port line. One slave machine is currently unable to be upgraded or continues to display the upgrade status. Step 1 Connect the serial port cable to the back of the machine. 2. Power on the mother machine---press the F4 key three times. 3. Sure. At this time, the mother machine panel displays ON. 4. When the handset is powered on and turned on, does the display appear chaotic? 5. When the upgrade starts, the motherboard display shows 001 to 099, then changes to E-P and finally changes to 001. Upgrade successful!

It is reported that the purpose of this upgrade of "ChinaStar 9" is to ensure that users of genuine set-top boxes can watch the original TV programs normally, and to attack all "black boxes" so that they cannot watch the programs normally. programme. The entire upgrade process lasts approximately 20 days. Every time there is an upgrade, there will be a batch of "black boxes" that cannot watch programs normally.

At the same time as this software upgrade, "ChinaStar 9" also added 20 sets of radio programs. Previously, Haier, Guoxin, Huaya, and Ali were involved in the development of the upgrade software for Vitex 9. The development was closed for three weeks. Currently, a cracking plan already exists. Due to the pressure from the General Administration, can the cracking plan be released or in what way? It is still uncertain whether the method will be launched into the market