Download the u startup v5.0 tool and install it on the local disk of the computer. How to install U-Boot v5 to the local disk of the computer? Look at the following graphic introduction:
1. The downloaded software is named "UQiDong_v5.exe".
2. Double-click "UQiDong_v5.exe" and follow the prompts to install.
Open the installation interface of U-start v5 installer, and we just need to click the "Start Installation" button!
We are installing U-boot v5 software on the local disk of the computer. We waited patiently for its progress bar to be completed. Please don't forcibly close the window during this time!
4 U-Boot V5 installs the interface after completion. Click "Start Making" to open the main window of the U disk making tool!
Step 2, run the USB flash drive making software to make USB flash drives.
1. After running u to start v5, the main window interface opens, as shown in the following figure:
2. In the red box marked by Bian Xiao, it says, "Please insert the USB flash drive that needs to make the startup disk first", and then we will insert the USB flash drive prepared in advance. (Note: 1. In order to ensure the data in the production process.
The transmission is smooth, please insert the U disk into the USB socket behind the main computer chassis.
If it is a notebook, plug it into any USB port at will. )
3. After inserting the USB flash drive, U begins to automatically identify the details of the USB flash drive: in the red box labeled Bian Xiao.
Shows the details of automatic identification of USB flash drive (u starts Bian Xiao with Kingston's 8GB disk).
Next, we click the "one-click USB flash drive" button, the button marked in the red box:
When you click the button to start the USB flash drive, a warning window will pop up. The content of the warning is to tell you that the U disk will be formatted and all the data in the U disk will be emptied, so you can confirm that there is no important data in the U disk and then click the "OK" button to start production. If you still have important file data in your USB flash drive, we will click the "Cancel" button, then copy the files and data in the USB flash drive to other disks of the computer, and then start production. As shown in the figure below:
After we click the "OK" button, all we need to do is wait patiently for the production to be completed. The production process includes: data preparation → formatting U disk → writing data → after production.
Unplug the USB flash drive automatically. "These processes are fully automatic without manual intervention and operation.
So in this process, please try to avoid doing other irrelevant operations to avoid production failure.
Until the USB flash drive is made successfully. As shown in the following four pictures, the whole production process: (the whole process takes about 1-2 minutes, and there may be a state of suspended animation at the initial stage of production, so don't worry, just wait), and the following picture shows the relevant data required for automatically preparing to start the USB flash drive.
6 is automatically formatting the U disk that needs to be made into a startup disk.
7. Write relevant data into USB flash drive.
After the 8u disk startup disk is successfully made, the U disk startup software is pulling the U disk for you.
In other words, it automatically pops up the USB flash drive and then inserts it. (because you need it after you make the boot disk.
Pull and insert once to test whether the production is successful)
After the USB flash drive is successfully made and automatically inserted, a window will pop up for you to test the USB flash drive.
For the selection box of whether the disk was made successfully, you can click the "Yes (Y)" button to test whether the U disk was made successfully.
Make a u disk startup disk. If we don't think it is necessary, then we can click "No (n)".
10 and then close the u startup software.
1 1 When we click the "Yes (Y)" button, a window of "Computer Simulator" will pop up, and the computer simulator will simulate the interface where the computer starts the U disk, that is, the main interface of U booting (Note: the computer simulator only provides the purpose of testing whether the U disk is successfully started, so please don't test tools such as PE).
12 computer simulator tests the USB flash drive startup interface. We can press the up and down keys to select it, without doing anything else. After the test, we can press "Ctrl" and "Alt" at the same time, release the mouse to the computer desk, then close the computer simulator window, and finally close U to start the main program. 7. Finally, let's check the USB flash drive and open it to check the file changes inside. The files and folders contained in the successful USB flash drive are "GHO folder", "My tools" and "U startup disk cloning tool".
13, the USB flash drive startup disk is finished.